Skip to content
Vektör Enerji
Product groups · 03

Cable and Connection

The complete connection chain: power and control cable, terminal blocks, cable lugs and marking systems.

Power, control, terminals, termination

9sub-categories

Our approach

Cable supply is driven by cross-section calculation, voltage drop and environmental conditions. Working with Seval Kablo and Erse Kablo, we ship standard sizes from stock and project quantities by the drum. On the connection side, Onka rail terminals, Konsan marking systems and Eurowest cable lugs let the entire in-panel assembly ship on a single delivery note.

What this group covers

  • NYY, NYA, NYAF power cables
  • Control and signal cables
  • Screened and halogen-free cables
  • DIN rail and feed-through terminals
  • Distribution blocks
  • Compression and bimetal cable lugs
  • Heat-shrink tubing
  • Cable marking rings and systems
  • Cable socks
Selection guide

How to choose the right product in this group

These are the same criteria we check when preparing a quotation. Send us your list and we run these checks on your behalf.

  1. 01

    Current-carrying capacity

    Catalogue ratings assume reference conditions. Ambient temperature, installation method and grouping reduce them; derating factors must always be applied.

  2. 02

    Voltage drop

    On long runs the deciding criterion is usually voltage drop rather than current. A limit around 3% for lighting and 5% for power circuits is accepted.

  3. 03

    Screening

    The motor cable on a drive output should be screened with the screen earthed at both ends. Otherwise noise appears on sensor and communication lines and RCDs trip without reason.

  4. 04

    Termination quality

    Lugs, tubing and crimping tools must match the conductor size. Incorrect crimping raises contact resistance, causing heating and eventual failure.

Common mistakes on site

The mistakes we meet most often on site

  • Sizing on current alone without checking voltage drop.
  • Exceeding the fill ratio in trunking, leaving no room for later additions.
  • Earthing the screen at one end only and never solving the EMC problem.
  • Postponing terminal marking until it never happens.
  • Using a single crimping tool for every conductor size.
Technical terms

Terms you will meet in quotations and specifications

The concepts that come up most often in correspondence about this group, with short definitions.

Voltage drop
The percentage of voltage lost along the run. Limits of around 3% for lighting and 5% for power circuits are accepted.
Derating factor
Reduction of current capacity for ambient temperature, installation method and cable grouping.
NYY / NYA / NYAF
NYY is a fixed-installation power cable, NYA a single-core rigid conductor and NYAF a flexible conductor used inside panels.
Screen and earthing
The conductive layer that limits interference on drive output cables. The screen must be earthed at both ends.
Frequently asked questions

Frequently asked about Cable and Connection

Can I buy cable by the drum?

Yes. Standard sizes ship from stock by the metre, and project quantities by the drum. For large quantities we give a date based on the production schedule.

When is halogen-free cable required?

It can be a specification requirement on escape routes, enclosed car parks, data centres and busy indoor spaces. It is preferred because it produces less smoke and corrosive gas in a fire.

Do you calculate the cable size?

Yes. Send the load, run length and installation method and we check current capacity, voltage drop and short-circuit withstand together, then recommend the size. There is no separate charge for this.

Can I order terminals and lugs on the same order?

Yes. With Onka rail terminals, Eurowest lugs and Konsan tubing and marking materials we consolidate the whole in-panel connection onto one delivery note, and include matching lug and crimping tool suggestions in the quotation.

Which cable colours should be used?

The protective conductor is green-yellow and the neutral light blue as standard. Brown, black and grey are common for phases. In control circuits, separating colours by voltage level makes fault-finding easier.

Contact

Have a project or a material list?

Send us your list; we return stock status, lead time and wholesale pricing the same day.

Sales line

+90 232 433 66 69+90 532 062 67 19info@vektorenerji.com.tr

Monday – Friday · 08:30 – 18:30

CallWhatsAppDirections